3D printed & assembled in St. Louis, Missouri Independent studio · Not affiliated with, endorsed by, or licensed by the LEGO Group
megafig.shop
A Mega Figure in the classic colorway — yellow head, red torso printed megafig.shop, cobalt legs
Actual size · 4 cm Scroll to scale up

megafig.shop

The minifigure you know. Just much much bigger.

Shop the Megafig

Series 01 · Editions of 50 / 30 / 20

Minifigure geometry, built at gallery scale.

Collector-grade blocky figures at 500%, 1000% and 1500% of a standard minifigure. Every one comes fully apart into its true component pieces — head, torso, arms, hands, hips, legs — exactly like the minifigures we all grew up with, just far bigger. Printed and hand-finished in our St. Louis workshop.

Browse the catalog Configure a figure
24"Max height
FullySeparable
100%Made in USA
Fig. A — component separation · Standard Issue at 1500%
The Octan Vintage Racer turned through a full revolution — front, right side, back and left side
Head
Separated Mega Figure head
Torso
Arms
Hands
Mega Figure torso with arms and hands attached
Hips &
Legs
Mega Figure hip and leg unit
Head · Torso · 2 arms · 2 hands · Hips · 2 legs Assembled
A 24-inch gloss Mega Figure standing on a piano lid beside a standard minifigure, shot from below against a sunlit window
1500% · beside the one you already own

Actual size

It is bigger than the photographs make it look.

Every other picture on this site is shot against white, where a figure has nothing to be large next to. This is the 1500% build on a piano lid, with a standard minifigure at its feet for the only comparison that really lands.

Same master geometry as every other scale — nine separate prints, sanded back and clear coated until the surface reads like a car panel.

See the range
01
Three sizes

500%, 1000% and 1500% builds off one master model.

02
Fully separable

Every piece pulls apart and clicks back together, just like the originals.

03
Poseable joints

Rotating head, arms and legs with tuned resistance.

04
Printed in St. Louis

Domestic filament, in-house printing, hand sanding and clear coat.

05
Limited drops

Numbered editions, retired for good once the run closes.

Current editions

All 10 pieces →
An oversized blocky figure in a vintage service livery — white torso with a red and green roundel, sage green legs and a yellow head
VINTAGE LIVERY $150 off at 1500%
Octan Vintage Racer
1000% & 1500% · NUMBERED
From $299 10 / 20 by size
The Classic Mega Figure in high gloss — yellow head, red torso and arms, cobalt legs — with the plain chest it ships with, photographed against white
THE ORIGINAL $150 off at 1500%
The Classic
500%–1500% · LOGO OPTIONAL
From $99 50 / 30 / 20 by size
A Mega Figure printed in wood-filled filament and stained American Walnut, the grain visible across the torso
REAL WOOD $150 off at 1500%
Wood Edition
1000% & 1500% · STAINED & SEALED
From $239 25 / 15 by size
Standard Issue giant 3D printed Mega Figure with red torso, cobalt legs and yellow head
SERIES 01 $150 off at 1500%
Standard Issue
500%–1500% · FULLY SEPARABLE
From $69 50 / 30 / 20 by size
A large red Mega Figure standing over a toy city skyline, from the Think Big commercial 8 spots · 139 seconds

From the archive that never was

We made the ads
this would have had in 1987.

Eight spots, most of them shot the way they would have been if any of this had existed back then — 4:3, film grain, a shopping mall, a cardboard skyline, and a hard cut to the logo.

Roll the tape

Scale study

Pick the scale. The price follows.

Every scale is printed from the same master geometry, so proportions and part separation stay identical from desk-size to floor-standing. Move the slider to see each size against a standard minifigure.

Scale
1000%
Height
16"
Weight
1.361 kg
Print time
~40 hr
From
$199
Side note

Every figure is offered in three sizes — 500%, 1000% and 1500% of a standard minifigure — shown below against one — move the slider to see each one.

Selected: 1000%
16-inch Mega Figure shown beside a standard minifigure for scale
A Mega Figure standing on a living-room floor beside an adult, showing how large the figures are in a room
At home, beside an adult

Who buys them

The gift for the person who already owns everything.

A giant 3D printed Mega Figure is the rare gift that cannot be bought at a mall or ordered twice — a numbered, hand-finished art object for the collector, executive, or friend who has run out of things to want. At 8, 16 or 24 inches tall it reads as sculpture on a shelf, a console, or a gallery floor, and it starts a conversation the moment someone walks into the room.

It is also the obvious present for lifelong LEGO enthusiasts and brick builders: an oversized blocky figure with fully separable head, arms, hands, torso and legs, rotating joints, and the same satisfying build logic they grew up with — scaled up until it dominates the room. Popular as a milestone birthday gift, a retirement or graduation piece, an office desk statement, a nursery centerpiece, and a Father's Day or Christmas surprise for the collector in the family.

Custom colorways, monthly limited drops, and made-to-order builds ship from St. Louis in three to four weeks — anywhere in the United States and Canada, with US freight included on orders over $100.

A painter in a respirator hood clear coating a Mega Figure torso inside the studio booth, with legs, arms and a head hung on stands around it

The studio

Original art objects, made by hand in St. Louis.

Each figure is modeled in-house, printed on our own machines, then sanded and clear coated by a two-person team. Nothing is outsourced and nothing ships without a signed edition card.

megafig.shop is an independent studio producing original sculptural work. We are not affiliated with, endorsed by, sponsored by or licensed by the LEGO Group, and our figures are custom art creations rather than construction toys.

How they're made